How Does a Bearing Buddy Work | Mechanism Explanation 2023

Last Updated on August 16, 2023 by Jisan

Bearing Buddies are devices that are used to keep bearings lubricated and free of water. The device consists of a housing that encloses the bearing and a piston that fits snugly inside the housing. The piston has a small hole in it that allows grease to be forced into the bearing when the piston is pushed down.

Bearing buddies are devices that are placed on boat trailers to keep the bearings in the hubs from becoming seized. The device consists of a spring-loaded plunger that fits into a housing. When the trailer is not being used, the plunger keeps the bearings lubricated.

When the trailer is being towed, the plunger pushes out on the bearing, keeping it from seizing up.

How to Check Grease Level in Bearing Buddy

If you have a Bearing Buddy on your trailer, it’s important to check the grease level periodically. Here’s how: 1. Park your trailer on level ground and set the parking brake.

2. Remove the dust cap from the top of the Bearing Buddy unit. 3. Use a flashlight to look inside the unit. You should see grease at least halfway up the sides of the unit.

If not, it’s time to add more grease. 4. To add grease, remove the fill plug from the side of the unit and insert a greasing gun into the fill hole. Pump in enough fresh grease until you see it overflowing from inside the unit (this is why it’s important to do this on level ground).

Wipe away any excess grease that comes out around the fill hole. 5. Replace both plugs (dust cap and fill plug) and you’re done!

How to Grease Bearing Buddies

If you have ever wondered how to grease bearing buddies, wonder no more! This helpful guide will show you everything you need to know. Bearing buddies are devices that are placed on boat trailer axles in order to keep the bearings lubricated.

They work by slowly releasing grease into the bearings as they rotate. This helps to prevent wear and tear on the bearings, and keeps them running smoothly. Greasing your bearing buddies is a fairly simple process, but there are a few things you need to keep in mind.

First, make sure that you have the proper type of grease for your particular model of bearing buddy. Second, always clean the area around the zerk fitting before attaching the grease gun. This will help to prevent contamination of the new grease.

Finally, be sure not to over-grease the bearings – too much grease can actually cause damage. With these tips in mind, greasing your bearing buddies should be a breeze!

How to Install Bearing Buddies

If you’ve ever had to replace a wheel bearing, you know how important it is to keep them properly lubricated. That’s where Bearing Buddies come in. They are designed to keep water and dirt out of your bearings while providing the proper amount of grease for protection.

In this article, we’ll show you how to install Bearing Buddies on your trailer so you can hit the road with confidence. The first step is to remove the old dust cap from the hub. You’ll need a hammer and chisel for this.

Once the old cap is removed, clean out any debris from the hub before proceeding. Next, take a look at the inner surface of the hub where the Bearings will sit. If there are any grooves or damage, now is the time to repair or replace the hub.

With a clean and undamaged surface, place one of the Bearing Buddies into the hub until it’s flush with the outer edge. Make sure that the greased fitting on the Buddy is facing outward. Repeat this process for each wheel on your trailer.

Now it’s time to re-install your wheels and hitched up!

Bearing Buddy Maintenance

If you own a boat, it’s important to keep your Bearing Buddies in good working order. Here are some tips for maintaining your Bearing Buddies: 1. Check the grease level in your Bearing Buddies regularly.

If the grease level is low, add more grease until it reaches the proper level. 2. Inspect your Bearing Buddies for any damage or wear. If you see any damage, replace the damaged parts immediately.

3. Clean your Bearing Buddies periodically with soap and water. This will help remove any build-up of dirt or grime that can cause them to work less efficiently. By following these simple tips, you can keep your Bearing Buddies working properly and help extend the life of your boat trailer bearings!

How to Repack Trailer Wheel Bearings With Bearing Buddies

If your trailer has Bearing Buddies, repacking the wheel bearings is a pretty easy job. You’ll need to have a few tools on hand, including a socket set, a screwdriver, and a hammer. You’ll also need some fresh grease and some new seals.

Here’s how to do it: 1. Jack up the trailer and remove the wheels. 2. Use a socket to remove the nut that holds the hub cap in place.

3. Pull off the hub cap and then use a screwdriver to remove the cotter pin from the axle shaft. 4. Pull out the axle shaft and then use a hammer to knock out the old inner bearing races from the housing. Be careful not to damage the housing in the process.

5. Clean out any old grease or debris from inside the housing with a rag or compressed air.

Credit: thepopupprincess.com

Do Bearing Buddies Actually Work?

If you’ve ever had a flat tire, you know the frustration of trying to fix it. You might have even considered getting a new tire, but then you remember that they’re expensive. Bearing Buddies are an affordable way to keep your tires in good shape and extend their life.

But do they actually work? Bearing Buddies are designed to keep water and debris out of your bearings, which can cause them to fail prematurely. They’re also supposed to provide a layer of protection against corrosion.

So, how well do they actually work? There are mixed reviews on Bearing Buddies. Some people say that they’ve kept their bearings in good condition for years, while others have had problems with them failing soon after installation.

It’s hard to say definitively whether or not Bearing Buddies work because there are so many variables at play (type of bearing, quality of product, etc). However, if you’re looking for a way to protect your bearings and extend their life, Bearing Buddies may be worth a try.

Do Bearing Buddies Grease the Inner Bearing?

If you have ever wondered whether or not Bearing Buddies grease the inner bearing, the answer is no. Bearing Buddies are designed to keep water and debris out of your boat trailer bearings, not to lubricate them. Lubrication is important for boat trailer bearings, but it must be done separately from using Bearing Buddies.

Do You Need to Repack Bearings With Bearing Buddies?

If you’re wondering whether or not you need to repack your bearings with Bearing Buddies, the answer is most likely yes! These devices are designed to keep water and dirt out of your boat trailer’s wheel bearings, and they do a great job at it. However, over time they can become clogged with grime and debris, which can cause them to wear out prematurely.

That’s why it’s important to regularly inspect and clean your Bearing Buddies, and repack them with fresh grease every few months. Doing so will extend the life of your bearings and help prevent costly repairs down the road.

How Often Should You Grease Bearing Buddies?

Bearing Buddy explanation & Greasable axle spindle

Conclusion

Bearing Buddies are a great way to keep your bearings in good shape and extend their life. They work by keeping the bearing area clean and free of debris, while also providing a constant flow of grease to the bearings. This helps to reduce friction and wear, and keeps the bearings running smoothly.